How To Know If Ps3 Controller Is Charging

Download Commodity

Download Article

This wikiHow teaches you how to prepare a PS3 controller. One of the well-nigh common bug with PS3 controllers is random push button pushes. There is a adequately piece of cake set up to this problem, but it volition require disassembling your controller. Other bug you may encounter are dislodged analogue sticks, and water damage.

i

Remove screws from the back of the controller. In that location are v screws holding the controller together. There are two on the top and bottom of both sides, and one on the peak heart.
two
Remove the dorsum. Yous may need to pry open the controller with a apartment head screwdriver. Open up information technology from the bottom and advisedly tilt it towards the top shoulder buttons.
- Be very careful that you don't accidentally dislodge the R2 or L2 trigger buttons while removing the back. They can exist pain to put back on.
Advertising
3
Remove the bombardment. The bombardment is the grey square piece on the dorsum of the motherboard. You don't need to disconnect the bombardment. You can only pull it upwardly out of it's holder and move it to the side.
- If you practise decide to disconnect the battery, pull on the white plastic office that the wires are connected to. Practice non pull on the wires.
iv

Remove the screw on the motherboard. The motherboard screw is located on the lesser of the motherboard next to the analogue stick.
5
Remove the motherboard. Carefully pull the motherboard upwardly and tilt it abroad from the shoulder buttons.
- Once once again, be careful not to accidentally dislodge the R2 and L2 trigger buttons.
6

Elevator the green ribbon and pull it back. The green ribbon is located at the top of the controller forepart. Information technology's above the hole where the left analogue stick goes. Place a flat head screwdriver under the ribbon and advisedly lift information technology up over the 2 plastic pins that are sticking upwardly out of the controller. Be conscientious not to tear or damage the ribbon. You will see a strip of black foam underneath the ribbon.
7

Remove the blackness foam strip. Over time, the foam strip gets compressed and the connectors on the ribbon aren't able to brand contact with the motherboard. This is why the controller is not working properly.
8
Identify record on the bottom of the black cream strip. For the all-time results, cutting a strip of thick double-sided tape the same length and width as the black foam strip. Place it nether the foam strip. Use scissors to cutting off any excess tape from the sides.
- If you don't have thick double-sided tape, you can cut about an inch-and-a-half of black electrical tape and whorl information technology upwardly into a tube. ^[ane]
ix

Supercede the foam strip. With the tape underneath the cream strip, you can at present place the cream strip back nether the ribbon.
10

Replace the ribbon. Pull the ribbon over the cream and place the ii holes over the pins that are sticking up out of the controller. Make sure it is firmly in place.
11

Clean the ribbon. Since the controller is open, it's non a bad idea to use a tissue or cotton wool bandy to wipe any grit away from the ribbon.
12

Clean the motherboard connector. If you wait at the motherboard, you volition come across a box that is a darker shade of green with some metal connectors sticking out of it. Information technology's higher up the left counterpart stick. This is where the motherboard connects to the ribbon. Use a tissue or cotton bandy to wipe the connectors on the female parent board.
13

Replace the motherboard. Carefully place the motherboard dorsum in it's place with the analogue sticks freely able to move through the holes.
14

Screw the motherboard back in place. Using the same spiral you took out of the motherboard, spiral it dorsum in at the bottom adjacent to the right analogue stick.
xv

Supervene upon the battery. The motherboard has a plastic holder on information technology's back that holds the bombardment in place. Place the battery back in the holder.
16
Supercede the controller back. To replace the controller dorsum, place the the thin office that goes in between the two shoulder buttons at the meridian of the controller in place. Carefully tilt the dorsum over the R2 and L2 trigger buttons and firmly push it back in place at the bottom of the controller.
- Be careful not to accidentally dislodge the R2 and L2 trigger buttons.
17

Supercede the screws on the controller back. In that location are five screws that hold the controller together. Replace the two on the sides, and the 1 in the middle. Your controller is now fixed.^[2]

Advert

1

Remove screws from the dorsum of the controller. In that location are five screws holding the controller together. There are 2 on the summit and bottom of both sides, and i on the top middle.
2
Remove the back. Y'all may need to pry open up the controller with a apartment head screwdriver. Open it from the bottom and carefully tilt it towards the top shoulder buttons.
- Be very careful that you don't accidentally dislodge the R2 or L2 trigger buttons while removing the dorsum. They can be pain to put back on.
3
Remove the battery. The battery is the large grayness square on the back of the motherboard. Y'all don't need to disconnect the battery. You can just pull it up out of it's holder and motility it to the side.
- If you do decide to disconnect the battery, pull on the white plastic part continued to the circuit board. Don't pull on the wires.
4

Remove the screw on the motherboard. The motherboard spiral is located on the bottom of the motherboard next to the analogue stick.
5
Remove the motherboard. Carefully pull the motherboard upwardly and tilt it away from the shoulder buttons.
- Once again, be conscientious not to accidentally dislodge the R2 and L2 trigger buttons.
6

Place the plastic stick back on the metal rod. There is a D-shaped metal rod that sticks up out of the motherboard. Place the plastic analogue stick back on the metallic rod.
vii

Supercede the motherboard. Advisedly identify the motherboard back in it'due south place with the analogue sticks freely able to movement through the holes.
viii

Screw the motherboard dorsum in identify. Using the same screw y'all took out of the motherboard, spiral information technology back in at the bottom next to the right analogue stick.
9

Replace the battery. The motherboard has a plastic holder on it's back that holds the battery in place. Identify the battery back in the holder.
10
Replace the controller dorsum. To supersede the controller back, place the the thin part that goes in between the 2 shoulder buttons at the summit of the controller in place. Carefully tilt the back over the R2 and L2 trigger buttons and firmly button it back in place at the lesser of the controller.
- Be very careful not to dislodge the R2 and L2 trigger buttons.
11

Supersede the screws on the controller back. In that location are five screws that hold the controller together. Replace the two on the sides, and the 1 in the middle. Your controller is at present fixed.

Advertisement

1

Ability off the controller immediately. If the controller gets wet, turning off the ability immediately volition prevent the circuit lath from shorting out.
ii

Remove screws from the back of the controller. There are five screws holding the controller together. There are two on the top and bottom of both sides, and one on the top center.
3

Remove the back. You may need to pry open the controller with a apartment head screwdriver. Open up information technology from the lesser and carefully tilt it towards the top shoulder buttons.
iv

Disconnect the battery. The battery is the large grey square on the back of the motherboard. To disconnect the battery, pull the white plastic piece that connects to the motherboard. Practise non pull on the wires. Pull on the plastic piece.
5

Place the controller under a lamp, fan, or window. This will help the water in the controller evaporate.
6

Wait at least 24 hours. To ensure the controller is completely dry out wait 24 hours, or longer.
seven

Reconnect the battery. Supercede the white plastic part that the battery wires are connected to back in the white plastic connector on the side of the motherboard.
8
Replace the controller back. To supplant the controller back, place the the thin function that goes in between the two shoulder buttons at the pinnacle of the controller in place. Carefully tilt the back over the R2 and L2 trigger buttons and firmly push it back in place at the bottom of the controller.
- Be careful not to accidentally dislodge the R2 and L2 trigger buttons.
9

Replace the screws on the controller back. There are five screws that hold the controller together. Replace the ii on the sides, and the ane in the middle.
10

Test the controller. To properly examination the controller, launch a game that utilizes all the buttons on the controller (like Minecraft). Test every button to make sure they are exercise what they are supposed to exercise. If all the buttons are working, the controller is stock-still. If there is any random push presses, or buttons not working, the motherboard has a short in it. You will need to replace the controller.

Advert

Add New Question

Question

How do I fix a scratched PS3 disk?

Try putting mint Colgate toothpaste on it, just a tiny dab. Gently wipe the excess toothpaste off with a paper towel. Y'all can see some different methods in the commodity How to Set up a Scratched CD.
Question

How do I prepare an analog stick that sometimes gets stuck in certain positions?

Usually, it's merely muddied. Open it as described and clean it with some booze.
Question

My dualshock's bombardment is yet unusable after two hours of charging. All the lights are blinking for 2 hours but nonetheless can't use it. What's the trouble and how to fix it?

Toasterflame

Top Answerer

It may be that the bombardment on your controller has failed. Many repair shops can replace the battery for you. Or, if you are familiar with electronic repair, you tin can notice many guides on this site to mend it yourself.
Question

Should I accept it to a repair store instead?

Bustertiko

Community Reply

If y'all desire to ensure your PS3 controller is properly fixed, then yep, a repair shop is the best option. If you lot wish to save money or accept no repair shops near your location, and then this article's instructions are a good culling.